Connecticut Electrician | Electrical Contractor, Residential and Commercial

Connecticut Electrician | Electrical Contractor, Residential and Commercial « CT Electrical Services

Providing responsible, courteous and SKILLED electrician services since 1994.

Electricians Serving Your Area:

Connecticut Cities
Allingtown, CT
Ansonia, CT
Beacon Falls, CT
Bethany, CT
Bethel, CT
Botsford, CT
Branford, CT
Bridgeport, CT
Brookfield, CT
Cheshire, CT
Cos Cob, CT
Danbury, CT
Darien, CT
Derby, CT
East Haven, CT
Easton, CT
Fairfield, CT
Georgetown, CT
Greens Farms, CT
Greenwich, CT
Guilford, CT
Hamden, CT
Hawleyville, CT
Madison, CT
Meriden, CT
Middlebury, CT
Milford, CT
Monroe, CT
Naugatuck, CT
New Canaan, CT
New Fairfield, CT
New Haven, CT
Newtown, CT
North Branford, CT
North Haven, CT
Northford, CT
Norwalk, CT
Old Greenwich, CT
Orange, CT
Oxford, CT
Prospect, CT
Redding Ridge, CT
Redding, CT
Ridgefield, CT
Riverside, CT
Rowayton, CT
Sandy Hook, CT
Seymour, CT
Shelton, CT
Sherman, CT
South Britain, CT
South Norwalk, CT
Southbury, CT
Southport, CT
Stamford, CT
Stevenson, CT
Stony Creek, CT
Stratford, CT
Trumbull, CT
Wallingford, CT
Waterbury, CT
West Haven, CT
West Redding, CT
Weston, CT
Westport, CT
Whitneyville, CT
Wilton, CT
Wolcott, CT
Woodbridge, CT
Yalesville, CT

Toll free in CT: 877-723-9052

Consumer Product Safety Commission

Use a Ground-Fault Circuit-interrupter With Every Power Tool

CPSC Document #5040

The U S. Consumer Product Safety Commission (CPSC) recommends the use of a ground-fault circuit-interrupter (GFCI) with every power tool to protect against electrical shock hazards. Each year, CPSC learns of approximately 20 to 30 electrocution deaths associated with power drills, saws, sanders, hedge trimmers, and other electric power tools. Most of these deaths could be prevented by the use of a GFCI.

A GFCI constantly monitors current flowing in a circuit to sense any loss of current. If the current flowing through two circuit conductors differs by a very small amount, the GFCI instantly interrupts the current flow to prevent a lethal amount of electricity from reaching the consumer. The consumer may feet a painful shock but will not be electrocuted. Grounding may provide some protection for power equipment and double insulation of newer power tools presents lower risks of electrocution. However, GFCls are the most effective means for protecting consumers against electrical shock hazards.

Since 1973, homes built according to the National Electrical Code have varying degrees of GFCI protection. GFCIs were first required in outdoor receptacle circuits In 1973, bathrooms in 1975, garage wall outlets in 1978, some kitchen receptacles since 1987, and all receptacle outlets in unfinished basements and crawl spaces since 1990.

Three common types of GFCls are available for home use: circuit breaker, receptacle and portable types. The circuit breaker type needs to be installed by an electrician. The receptacle type may be installed by knowledgeable consumers familiar with electrical wiring practices. The portable GFCI needs no special knowledge to install Just plug the portable GFCI Into a wall receptacle and then plug the electric power tool into the GFCI. It is generally priced below $30 and is available at hardware stores, building supply centers and electrical supply houses.

ELECTROCUTION HAZARD

Use a GFCI whenever you use a power tool, to prevent electrocution.

009109

Privacy Notice | Site Map | CTELECTRICAL.COM llc. | Phone: 203-723-9052 | Contact Us

Connecticut Electrician Services LLC
Beacon Falls, CT 06403

Our license # is 00123626. This is an Electrical Unlimited Contractors E-1 license from the State of CT Dept. of Consumer Protection.